MICOM P127 PDF

0 Comment

Technical Guide. P12y/EN T/C MiCOM P/P/P Page 1/2. MiCOM P/P & P Directional/Non-directional Relay. CONTENT. Safety Section . MiCOM P, P, P, P, P, P and P 3 Phase Overcurrent and Earth Fault Protection Relays. MiCOM P12x is a range of directional and. Download documents for MiCOM P, P, P, P, P, P and P – 3 Phase Overcurrent and Earth Fault Protection Relays.

Author: Faemi Gular
Country: Mayotte
Language: English (Spanish)
Genre: Music
Published (Last): 17 March 2009
Pages: 399
PDF File Size: 15.41 Mb
ePub File Size: 11.24 Mb
ISBN: 917-9-30784-342-9
Downloads: 94292
Price: Free* [*Free Regsitration Required]
Uploader: Mazil

The following displays and settings are only shown and applicable with the P relay. These LEDs can be programmed by the micom p on the basis of information on available thresholds instantaneous and time-delayed.

To gain access to the Transfo.

All rights are reserved. The setting range is from 57 to V, in steps of 0.

MiCOM P12y, Manual (global file) P12Y/EN M/Gb5 | Schneider Electric

The tripping zone for the directional protection function micom p27 p27 in the drawing. This website is not sanctioned or approved by any manufacturer or tradename listed.

MiCOM P12x offers a wide range of protection functions allowing its use in many applications including:. Communication protocol of the RS micom p port situated on the rear of the relay.

The setting range is from 0. Mcom depend on the selected electrical voltage connection mode. A request has failed and is being retried. To gain access to the next window press “. Please call or email us with your request. This jicom is represented by the characteristic reproduced below, where the hatched area is the tripping zone. A valid written repair rate from a valid competitor must be provided to confirm mocom price. The setting value is either 1 or 5.

  CPU SCHEDULING NUMERICALS PDF

The General Options submenu is not available for the P relay. Download and register now to get access to recommended services and more. LEDs should be in the following configuration: Radwell is not an authorized distributor or an affiliate of the Manufacturer of RISCN1 products; Radwell sources these products through independent channels including resellers, the original manufacturer not as micom p authorized distributorand online marketplaces, allowing Radwell to obtain competitive buying rates; The products are genuine, new in box, and unused; The products may vary micom p to country of origin, accessories and other items included with the ,icom, the language used on the packaging, parts and instructions, and the contents of any micom p material; For quality assurance purposes, some products may not have a factory seal.

MiCOM P12y, Manual (global file) P12Y/EN M/Gb5

Forward mlcom zone Torq ue A ngle Reverse tripping zone PENa The directional earth fault protection also provides a non-sensitive area to avoid instability due to small dissymetries and unbalances that can micom p be present in the systems.

MiCOM P12x is a range of directional and. This setting is only available in P and P relays. Select choice using the above instructions. Order must be processed before 3pm ET. Ratio Heading of Transfo.

MiCOM P12y, Manual (global file) P12Y/EN M/Gb5 | Schneider Electric

The available options are: Auxiliary power supply range. To gain access to the previous window press!. Micom p this message does not close after 30 seconds, please check your internet connection and try again. MiCOM P12x is a range of directional and non-directional overcurrent relays from single phase or earth fault up to the multifunctional three-phase P device with micom p protection functions. This error most likely means that your internet connection is not working.

  BUCKE COSMIC CONSCIOUSNESS PDF

In p172 example, the power supply must be a DC voltage. To navigate within submenu points, press!

Next to micim battery compartment there is a 9-pin female D-type socket, which micomm be used micom p communicate with a local Micom p up to 15m distance via a RS serial data link cable SK1 port.

Line VT sec This window is not available for the V model. The tripping zone is limited by the equation: Turn on the auxiliary power supply and set to micom p rated voltage as shown on the front panel of the relay.

The setting value is either 1or 5.

The rated voltage input range is given by relay Cortec code. General Options Heading of General Options submenu. Temporary powering of micom p relay in order to allow the user to view or modify data when the auxiliary power supply has failed.

Presentation Presentation Documents micom p Downloads. Each item on the label is described below: Micpm another country or region.

To reach the LED configuration submenu press ” for Led 5. Ue Ie Tripping zone is settable from: Enviado por Alexandre flag Denunciar.

Sell us your inventory. Each LED illuminates when the associated information is valid. Sensitivity of the earth fault current available are p17 sensitivity levels. The setting range is from 1 to The display should show: Applications MiCOM P12x offers a wide range of protection functions allowing its use in many applications including: To modify this default value, follow the above instructions.