HT12D AND HT12E DATASHEET PDF

0 Comment

HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. Robokits India HT12E & HT12D Encoder and Decoder IC for RF Modules [RKI- ] – The HT 12E Encoder ICs are HT12E Datasheet · HT12D Datasheet.

Author: Sataur Dot
Country: Andorra
Language: English (Spanish)
Genre: Life
Published (Last): 16 March 2009
Pages: 269
PDF File Size: 10.8 Mb
ePub File Size: 19.10 Mb
ISBN: 693-5-42985-281-7
Downloads: 88563
Price: Free* [*Free Regsitration Required]
Uploader: Grorn

Interface SD Card with Arduino. Photograph just for reference. As soon as TE returns to high, the encoder output completes its final cycle dqtasheet then stops.

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. Buy 15 or more pieces to get Free Shipping Option Availability: This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. This oscillator can be used by connecting these two pins through a 1M Resistor.

Connected to the Ground of circuit. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. You can know to set up the HT12D after this from here. This pin has to be connected to Ground 0V to enable the Transmission. It is mainly used in interfacing RF and infrared circuits. If you want security you can connect any of the 8 pins to 5V to make it high.

  DATASHEET 74153 PDF

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as datasheett, by connecting all address pins to ground.

It is very important that your Decoder should have the same address of that of the encoder. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The IC is has a wide range of operating voltage from 2.

Be the first to write a review. Submitted by admin on 27 October Choosing Motor For Robots. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Transmission enable; active low. The Yt12d is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

HT12E Encoder IC

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Arduino based GPS receiver.

This cycle is repeated as long as TE is kept low. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product.

Customers who bought this product also purchased The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Full Name Email Address. TL — Programmable Reference Voltage. The Encoded 12 bit output data obtained from HT12E has to be given here. This high-density System-in-Package SiP integrates controller, power switches, and support components.

  GAMES WORKSHOP EAVY METAL MASTERCLASS PDF

Can range from 2. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. The IC has a built in oscillator. This ICs are paired with each other. They can also be connected to LED to physically view the received data. Supply voltage; 5V 2. These are the 8-bit address bits, which is used to protect your data.

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. Thanks a lot for helping us to maintain competitive prices. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

These 12 bits are divided into 8 address bits and 4 data bits. HT12E is an encoder integrated circuit of 2 12 series of encoders. Found this item with same quality and at a lower price but prefer to buy from robokits.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

They are paired with 2 12 series of decoders for use in remote control system applications. This pin powers the IC should use only datasheeg. They are capable of Encoding 12 bit of information which consists of N address bits and N data bits.