1 Jan Buy ASTM D PRACTICES FOR EVALUATING THE RESISTANCE OF PLASTICS TO CHEMICAL REAGENTS from SAI Global. Current edition approved April 1, Published June Originally www. 4 approved in Last previous edition approved in as D Published June Originally approved in Last previous edition approved in as D – 95 (). DOI: /D ASTM Standards
|Published (Last):||18 March 2007|
|PDF File Size:||1.58 Mb|
|ePub File Size:||4.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world. Base the selection of test conditions on the manner and duration of zstm with reagents, the temperature of the system, applied stress, and other performance factors involved in the particular application.
Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use.
A total of 30 laminate satm were tested: What is Third Party Certification and Accreditation for the food industry? Further testing is required to verify that BOD greater than PPM significantly reduces the laminate flexural yield stress and flexural modulus.
It was found that two and half rotations produced the desired strain and that the strain level remained constant over a seven-day period. The choice of types and concentrations of reagents, duration of immersion or stress, or both, level of stress, temperature of the test, and properties to be reported are necessarily arbitrary. The device uses a three point bending design with coupon contact dimensions similar to those used in d5543 D test.
Evaluating the Resistance of Plastics to Chemical Reagents. Certification Formally confirming that your products and services meet all trusted external and internal standards. After the agreed upon period of time, the specimens are removed and evaluated for desired properties such as change in weight, appearance or tensile properties vs. Auditing Consulting Sourcing Training.
Chemical reagents can x543 lubricants, cleaning agents, inks, foods, or anything else that the test material may be expected to come in contact with. Astn are made for various exposure times, stress conditions, and exposure to reagents at elevated temperatures. If used as a container or transfer line, specimens should be immersed. Send us a request Wilton UK: It should also be noted that two of the coupons 1 lb and c show much higher stress-strain response than a.
This coupon was discarded and was atm used in the study. Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes.
Specimens can be weighed and measured prior to contact with the chemical reagent. Variations in the stress-strain response of coupons after immersion in 0.
This slight angle is a characteristic of the JetCut process. Posted by Tabitha at 8: Possible reasons for the lower response of coupon a are asym influence of BOD or a flaw in the test coupon cut from Plate It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This standard and ISO Part 3 address the same subject matter, but differ in technical content and the results cannot be directly compared between the two test methods. The test samples are then sealed in a container, and either left at room temperature or placed in an oven.
Unlike the BOD test coupons three-test coupon show relatively consistent stress-strain response. If the material will only see short exposures or will be used in proximity and reagent will splash or spill on the material, use the wet patch method of applying reagent. Active view current version of standard. Note 1 This standard and ISO Part 3 address the same subject matter, but differ in technical content and the results cannot be directly compared between the two test methods.
Specific hazards statements are given in Section 7. Weight and Dimensions Changes, test results indicate that the laminate product had no significant visible appearance changes after exposure to s543 chemicals reagent and that weight and depth changes are greater than width and length changes. The type of conditioning immersion or wet patch depends upon the end-use of the material.
Five percent Ammonium Hydroxide showed the greatest change 3. After the agreed upon period of time, the specimens are removed and evaluated for desired properties such as change in weight, appearance or tensile properties vs. These practices include provisions for reporting changes in weight, dimensions, appearance, and strength properties.